Batboard

Andreas

Install the proper firmware and reset the radio with the cps.

Andreas

Look here: http://agh-technik.orgfree.com/mototrbo.html

Andreas

I´m looking for a detailed service manual for a SL1600.

Andreas

Yes,it is possible,but useless.The radio have only a one digit display! You can dump in a CM360 codeplug with the EU Waris Lab Upgradekit.Don´t forget to save the tuning data,before you do it! You have to reload it after dumping.The serial number must be set,before you reload the tuning data.Don´t f...

Andreas

You can flash it with the front programming cable. Run the flashtool and let it read the EEPROM.Remove the cable and switch off the radio.Bridge the 2 right contacts of the microphone connector and switch the radio on.The buttons will light up and the display remains dark,so the radio is in bootstra...

Andreas

S Band is not supported by the 2100 series rss!The 2100 series rss is different from the MTS2000 rss.It´s the european version. The 2100 series RSS supports MC and MT2100 in one rss. For flashing,you need a modified RIB or my Unirib(you can find a schematic on my homepage) and the 2100 series (lab) ...

Andreas

If you don´t need MDC,you can flash them into MT2100 and you have 250 conventional channels!
No toolproof and you don´t need a SMARTRIB.The 2100 series RSS supports MB,VHF and UHF (<520MHz) only!

Andreas

Andreas

32 bit is always the best version for universal use!The 64 bit version,often makes trouble with older software.

Andreas

Andreas

You should try it with the Windows RSS.

Andreas

Andreas

No,the radio cannot decode DTMF tones!

Andreas

Andreas

The PLL is out of lock!
You have to retune the PLLs and the frontend.The bandsplit of this radio is only +/-2 MHz from a tuned frequency.

Andreas

Andreas

Du you have the jumper wire (pin9/pin10) in the accessory connector?

Andreas

Andreas

You have to disable the time out timer (Sendezeitbegrenzung).

Andreas

Andreas

Yes,that´s the problem!Commercial Seris CPS and MOTOTRBO CPS on the same PC can make problems.
Install your Commercial Seris CPS and 1225 CPS again.

Andreas

Andreas

1.)Never use a RIBLESS cable to make a firmware update.
2.)Always save the tuning data and write down the temperature compensation data of each radio,before you make the update.

Andreas

Andreas

You can use a modified CPS,to bypass the password protection.

Andreas

Andreas

You should try to dump in a new firmware with the US Waris Lab Flashkit.
Often the FLASHROM has corrupted firmware inside or it is defect.
If the bootloader is completely loaded into the radio and then you get an error message,replace the FLASHROM.

Andreas

Andreas

You can use Micedit.exe to set the min.volume to zero.
Micedit is a part of the Wookie Mobius 2100 series CPS.

Andreas

Andreas

You can us this to disable the cache:
http://www.agh-technik.orgfree.com/archiv/cache.zip
Always boot the PC with real DOS!

Andreas

Andreas

Disable the cache and try it again!

Andreas

Andreas

FlashZap Client and proper firmware should fix it.

Andreas

Andreas

The bandsplit is set in the codeplug.The radio is not out of lock! You have to dump in a codeplug with the higher bandsplit (s) and retune the radio! Look at my homepage (german language),for some modifications. Before you do something,read and save the native codeplug with MTSX Lab (or Jedi native ...

Andreas

You can use the 2100 series DOS RSS on this radio.Wookie Mobius is not a good choice on the mobile radios.You can get some errors with this beta stuff and the frontend tuning is blanked out.
Yes,it´s a good radio for ham use.

Andreas

Andreas

Remove the battery look at the led and switch the radio on.
If the LED flash up,you can try to fix it with the EU Waris Lab Upgradetool.

Andreas

Andreas

You have to create a simple Network with the network editor and load it with the RSS.

Andreas

Andreas

You can use a P I for this,even a P III works fine if you disable the CPU cache!
If you use Wookie Mobius,you can use a P IV,but Wookie make some trouble withe the mobile radios!

Andreas

Andreas

Hi!
You should try it with another PC.Don´t run it on Win7 or higher.Sometimes even Win XP makes trouble.

Andreas

Andreas

Nothing.
What´s the problem?

Andreas

Andreas

ENVN4037B

Andreas

It´s homemade stuff to dump in a new codeplug and flash firmware.

Andreas

Andreas

You can also try to fix it,with the unofficial US Waris Lab Upgradekit.
I hope,you´ve saved the tuning data,before the radio crashed!

Andreas

Andreas

Remove the battery for a short time and attach it.Switch the radio on and look at the LED.If you can see a short flash,do this: Take a good radio and make a regular firmware update.When the upgradetool tells you,that you must switch (the flash adapter) to on,change the radio with the bad one and cli...

Andreas

Activate "Repeater Talkaround" in the RSS!

Andreas

Andreas

You have to change the codeplug (model) with the codeplug tool from the US Waris Lab Upgradekit.
Save the tuning data,with the tuner software,before you do anything.

Andreas

Andreas

Toolproofing could only be an issue,if you don´t save the native codeplug of each radio,before you modify something! Use the read/write with no pack/unpack and read it.Go to "archive/srecords disk files" Type the serialnumber and save it with "write archive". Now you can play wit...

Andreas

Corrupted firmware inside!You have to reflash the firmware with EU Waris Lab Upgradekit.

Andreas

Andreas

Could be a FLASHROM or EEPROM error!
Before you change something,try to fix it with the EU Waris Lab Upgradekit.

Andreas

Andreas

Yes,MTSX-Lab 06.03.00 is out now,but I havn´t used it,to fix a toolproofed codeplug,yet.

Andreas

Andreas

Get and run HT800Lab.This stuff is less comfortable,but you don´t have much problems.

Andreas

Andreas

Taunusstein factory ca.1986-1990.Here,better known as MC-Compact.
It´s mainly made from MC-Micro parts.

Andreas

Andreas

If you really have a PW5 model and nobody flashed it with Skywalker or MP1327 firmware,you should try MCS/MTS2000 RSS AVN6028E or Smartnet Flight Number RSS (R03.01.00). Run MTSX-Lab or something like this (the Native Codeplug Programmer is eadier to handle).Read the native codeplug with no pack/unp...

Andreas

No!
Extracting won´t work.
Those files a special stuff in S-Records format.

Andreas

Andreas

With the unofficial homemade US Waris Lab Upgradekit.

Always save the tuning data,before you upgrade a radio or use this tookit!

Andreas

Put this into a text file and rename it to allreg.reg:

[HKEY_LOCAL_MACHINE\SOFTWARE\Motorola\ProRadio\FSK]
"SerializedString"="@%&MAHUS"

Click on and start it.
Now,you have all regions enabled.

Andreas

Andreas

Andreas

It will only work,with the GM firmware and codeplug s-record files!
You have to flash them with the 2100 series lab upgradetool.

Andreas

Andreas

Create a new codeplug with the 2100 series DOS RSS and dump it in with MTSX-Lab or a native codeplug programmer. Still problems? Flash the radio again,convert the codeplug with MTSX-Lab or a native codeplug programmer into a s-record and use the 2100 series lab upgradetool,to program the s-record in...

Andreas

First,you should try to program a default(MC2100) codeplug,with a Native Codeplug programmer or MTSX Lab.
If you still have problems,get the 2100 series lab upgradetool.Type X to get into the labmode.
For additional information,take a look at my homepage.

Andreas

Andreas

Did you try to flash it into a MC2100?
What kind of upgradetool is used for the GM1200?

Andreas

Andreas

Try to program it again!
If you can´t program it,you can fix it with the 2100 series lab upgradetool.
For this,you need a modified RIB or Unirib.

What shows the display on the corrupted radio?

Andreas

Search found 619 matches