Thanks, Alex.
I already fixed the addressing. It was just a 1 mistype and not a big (because both routers can call and receive calls; so, if initial call fails, another router will call back and vice versa).
But I am in the same situation as before. Routers now model 2811 with IOS 15, but still nothing working as it should. I can get working any link I need, Type 2 or Type 5. One codec or another. I do COS/COR signals and see proper current (7 mA; mist be greater than 3 mA), but I still see no audio via network. DSP shows busy state and packet count for ports used, but still no audio.
Also I switched to M-Lead instead of E-Lead, because as far as I found out, M-Lead is for COR/COS. Meanwhile, when I ground pin # 2 or short pins 1&2, and see no changes on other side. No audio, no PTT stated changes.
All 4 audio transformers, installed in EM cards, looks OK and shows 65 Ohm each at DC. SB provides -48.5 VDC well. "bootup e-lead off" and "no bootup e-lead off" commands works properly (in the second case I see 23 Ohm equivalent resistance on ping 7&8 during ISR reload). So, I can't tell that something wrong with E/M ports. Also, I see proper voltage changes when I change trunking Type (e.g. M-Lead become -48 VDC in Type 5, but SB become GND).
I have only some crazy ideas:
1. That ISRs needs routing enabled or some other IP core parameter(s);
2. That something was changed by jumper settings (not sure they are existing in this HW or not);
3. I need VoIP edition of IOS, but not AES;
4. Brand new E/M cards are fakes or "fried" (but I was the first person who touched them; they were new and w/o any fingerprints).
5. E/M ports have some "presence" sensors (seen nothing about in papers, but who why not?).
Now I want to find a new and fresh ideas what to do next. E.g.:
1. Recording audio from DSP by software to be sure that audio is inside and passed ADC properly.
2. To find COS/COR/PTT triggers (or their indicators) in console;
3. To run voice trunk inside one router, between 2 of E/M cards (just to be sure that they are OK);
4. To ensure that audio is above than VAD threshold (if enabled).
5. To ensure that M-Lead/E-Lead configured to provide expected results (
Cisco's tables 3-10, 3-11 and 3-12 looks monstrous and I am not sure which one is valid for regular trunking, but not multicast, unicast or PLAR).
If you can help with something, please do. I am totally exhausted and definitely will stop this project soon until any progress. I am not made of steel...
Below is all diag data valid at this moment:
Code: Select all
2811_1#show voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0 -- e&m-lmr up up trunked trunked n
0/0/1 -- e&m-lmr up up trunked trunked n
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
Code: Select all
2811_1#show voice call summary
PORT CODEC VAD VTSP STATE VPM STATE
============== ========= === ==================== ======================
0/0/0 g711ulaw y S_CONNECT S_TRUNKED
0/0/1 g711ulaw y S_CONNECT S_TRUNKED
Code: Select all
2811_1#show voice dsp detail
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
----------------------------FLEX VOICE CARD 0 -----------------------
-------
*DSP VOICE CHANNELS*
CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending
LEGEND : (bad)bad (shut)shutdown (dpend)download pending
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
====== === == ========= ========== ===== ======= === == ========= == ==== ============
C5510 005 01 g711ulaw 28.3.14 busy idle 0 0 0/0/1 01 0 0/536
C5510 005 02 g711ulaw 28.3.14 busy idle 0 0 0/0/0 00 0 0/548
C5510 005 03 None 28.3.14 idle idle 0 0 0 0/0
C5510 005 04 None 28.3.14 idle idle 0 0 0 0/0
C5510 005 05 None 28.3.14 idle idle 0 0 0 0/0
C5510 005 06 None 28.3.14 idle idle 0 0 0 0/0
C5510 005 07 None 28.3.14 idle idle 0 0 0 0/0
C5510 005 08 None 28.3.14 idle idle 0 0 0 0/0
*DSP SIGNALING CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT
====== === == ========= ========== ===== ======= === == ========= == ==== ============
C5510 005 01 {flex} 28.3.14 alloc idle 0 0 0/0/0 02 0 34/0
C5510 005 02 {flex} 28.3.14 alloc idle 0 0 0/0/1 02 0 34/0
------------------------END OF FLEX VOICE CARD 0 ----------------------------
R1 sh ver:
Code: Select all
2811_1#
2811_1#show version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(4)M12a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 04-Oct-16 03:37 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
2811_1 uptime is 8 minutes
System returned to ROM by power-on
System image file is "usbflash1:c2800nm-adventerprisek9-mz.151-4.M12a.bin"
Last reload type: Normal Reload
Cisco 2811 (revision 1.0) with 247808K/14336K bytes of memory.
Processor board ID
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
2 Voice E & M interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1958032K bytes of USB Flash usbflash1 (Read/Write)
62720K bytes of ATA CompactFlash (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO2811
Configuration register is 0x2102
R2 sh ver:
Code: Select all
2811_2#sho ver
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(4)M12a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 04-Oct-16 03:37 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T6, RELEASE SOFTWARE (fc1)
2811_2 uptime is 10 minutes
System returned to ROM by power-on
System image file is "usbflash1:c2800nm-adventerprisek9-mz.151-4.M12a.bin"
Last reload type: Normal Reload
Cisco 2811 (revision 1.0) with 247808K/14336K bytes of memory.
Processor board ID
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
2 Voice E & M interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1958720K bytes of USB Flash usbflash1 (Read/Write)
62720K bytes of ATA CompactFlash (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO2811
Configuration register is 0x2102
R1 sh run:
Code: Select all
2811_1#show run
Building configuration...
Current configuration : 2700 bytes
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 2811_1
!
boot-start-marker
boot system usbflash1:c2800nm-adventerprisek9-mz.151-4.M12a.bin
boot-end-marker
!
enable secret 5
enable password
!
no aaa new-model
!
dot11 syslog
ip source-route
no ip routing
!
no ip cef
!
ip domain name batlabs.com
no ipv6 cef
!
multilink bundle-name authenticated
!
voice class permanent 1
signal timing oos timeout disabled
signal keepalive disabled
signal sequence oos no-action
!
voice-card 0
!
crypto pki token default removal timeout 0
!
license udi pid CISCO2811
archive
log config
hidekeys
username password 0
username password 0
!
redundancy
!
ip tftp source-interface FastEthernet0/0
!
interface FastEthernet0/0
ip address 192.168.1.143 255.255.255.0
no ip route-cache
duplex full
speed auto
no mop enabled
!
interface FastEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
!
ip forward-protocol nd
ip http server
no ip http secure-server
!
snmp-server community batlabsDOTcom RW
!
control-plane
!
voice-port 0/0/0
voice-class permanent 1
auto-cut-through
operation 4-wire
type 2
signal lmr
lmr e-lead voice
lmr duplex half
lmr led-on
input gain 3
output attenuation -3
no echo-cancel enable
no comfort-noise
timeouts call-disconnect 3
timeouts wait-release 3
connection trunk 2110
description E/M Voice Port 0
!
voice-port 0/0/1
voice-class permanent 1
auto-cut-through
operation 4-wire
type 2
signal lmr
lmr e-lead voice
lmr duplex half
lmr led-on
input gain 3
output attenuation -3
no echo-cancel enable
no comfort-noise
timeouts call-disconnect 3
timeouts wait-release 3
connection trunk 2111
description E/M Voice Port 1
!
mgcp profile default
!
dial-peer voice 100 voip
description My LMR dial peer link 100
destination-pattern 2110
session target ipv4:192.168.1.144
codec g711ulaw
ip qos dscp 5 media
ip qos dscp 5 signaling
vad aggressive
!
dial-peer voice 101 pots
destination-pattern 1110
port 0/0/0
!
dial-peer voice 200 voip
description My LMR dial peer link 200
destination-pattern 2111
session target ipv4:192.168.1.144
codec g711ulaw
ip qos dscp 5 media
ip qos dscp 5 signaling
vad aggressive
!
dial-peer voice 201 pots
destination-pattern 1111
port 0/0/1
!
line con 0
line aux 0
line vty 0 4
exec-timeout 480 0
password 123
login local
transport input ssh
line vty 5 15
exec-timeout 480 0
login local
transport input ssh
!
scheduler allocate 20000 1000
end
R2 sh run:
Code: Select all
2811_2#sh run
Building configuration...
Current configuration : 2675 bytes
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 2811_2
!
boot-start-marker
boot system usbflash1:c2800nm-adventerprisek9-mz.151-4.M12a.bin
boot-end-marker
!
enable secret 5
enable password
!
no aaa new-model
!
dot11 syslog
ip source-route
no ip routing
!
no ip cef
!
ip domain name batlabs.com
no ipv6 cef
!
multilink bundle-name authenticated
!
voice class permanent 1
signal timing oos timeout disabled
signal keepalive disabled
signal sequence oos no-action
!
voice-card 0
!
crypto pki token default removal timeout 0
!
license udi pid CISCO2811 sn
username password 0
!
redundancy
!
ip tftp source-interface FastEthernet0/0
!
interface FastEthernet0/0
ip address 192.168.1.144 255.255.255.0
no ip route-cache
duplex full
speed auto
no mop enabled
!
interface FastEthernet0/1
no ip address
no ip route-cache
shutdown
duplex auto
speed auto
!
ip forward-protocol nd
ip http server
no ip http secure-server
!
snmp-server community batlabsDOTcom RW
!
control-plane
!
voice-port 0/0/0
voice-class permanent 1
auto-cut-through
operation 4-wire
type 2
signal lmr
bootup e-lead off
lmr e-lead voice
lmr duplex half
lmr led-on
input gain 3
output attenuation -3
no echo-cancel enable
no comfort-noise
timeouts call-disconnect 3
timeouts wait-release 3
connection trunk 1110
description E/M Voice Port 0
!
voice-port 0/0/1
voice-class permanent 1
auto-cut-through
operation 4-wire
type 2
signal lmr
bootup e-lead off
lmr e-lead voice
lmr duplex half
lmr led-on
input gain 3
output attenuation -3
no echo-cancel enable
no comfort-noise
timeouts call-disconnect 3
timeouts wait-release 3
connection trunk 1111
description E/M Voice Port 1
!
mgcp profile default
!
dial-peer voice 101 voip
description My LMR dial peer link 101
destination-pattern 1110
session target ipv4:192.168.1.143
codec g711ulaw
ip qos dscp 5 media
ip qos dscp 5 signaling
vad aggressive
!
dial-peer voice 100 pots
destination-pattern 2110
port 0/0/0
!
dial-peer voice 201 voip
description My LMR dial peer link 201
destination-pattern 1111
session target ipv4:192.168.1.143
codec g711ulaw
ip qos dscp 5 media
ip qos dscp 5 signaling
vad aggressive
!
dial-peer voice 200 pots
destination-pattern 2111
port 0/0/1
!
line con 0
line aux 0
line vty 0 4
exec-timeout 480 0
password 123
login local
transport input ssh
line vty 5 15
exec-timeout 480 0
login local
transport input ssh
!
scheduler allocate 20000 1000
end
R1 sh diag
Code: Select all
2811_1#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:20:26 ago
Onboard VPN : v2.3.3
EEPROM contents at hardware discovery:
PCB Serial Number :
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-04
Board Revision : A0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20080301
Chassis Serial Number :
Chassis MAC Address : 001f.9e5e.aab8
MAC Address block size : 24
CLEI Code :
Product (FRU) Number : CISCO2811
Part Number : 73-10258-05
Version Identifier : V05
EEPROM format version 4
EEPROM contents (hex):
PVDM Slot 1:
8-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8848-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number :
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-8
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
2nd generation - E&M Voice daughter card (2 port)
Hardware Revision : 5.1
Top Assy. Part Number : 800-23669-03
Board Revision : A0
Deviation Number : 0-0
Fab Version : 05
PCB Serial Number :
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V01
Product (FRU) Number : VIC2-2E/M
CLEI Code :
EEPROM format version 4
EEPROM contents (hex):
R2 sh diag
Code: Select all
2811_2#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:22:15 ago
Onboard VPN : v2.3.3
EEPROM contents at hardware discovery:
PCB Serial Number :
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-04
Board Revision : A0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20080301
Chassis Serial Number :
Chassis MAC Address : 001f.9e5e.ab18
MAC Address block size : 24
CLEI Code :
Product (FRU) Number : CISCO2811
Part Number : 73-10258-05
Version Identifier : V05
EEPROM format version 4
EEPROM contents (hex):
PVDM Slot 0:
8-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8848-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number :
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-8
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
2nd generation - E&M Voice daughter card (2 port)
Hardware Revision : 5.1
Top Assy. Part Number : 800-23669-03
Board Revision : A0
Deviation Number : 0-0
Fab Version : 05
PCB Serial Number :
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V01
Product (FRU) Number : VIC2-2E/M
CLEI Code :
EEPROM format version 4
EEPROM contents (hex):