cp200 programming problems

fireman54 · Post by **fireman54** » Sat May 20, 2006 2:09 pm

Do I or do I not need a rib to program a cp200 the cable I got with the radio's does not plug into my rib.

I get error code 512 when I try to read the radio ribless.

Please help I am going out of my mind

Thanks

HLA · Post by **HLA** » Sat May 20, 2006 4:02 pm

open up the connector and see if there is a rib inside of it.

fireman54 · Post by **fireman54** » Sat May 20, 2006 4:12 pm

No rib inside of cable I have the cable that does the p1225, cp200 gp300 etc and just a plain cable also both give me the same error and neither cables will plug into my rib it is a 9 pin connector cable

Is there an adapter?

fireman54 · Post by **fireman54** » Sat May 20, 2006 4:19 pm

also I am using rss for the 150 and 200.

Post by **escomm** » Sat May 20, 2006 7:36 pm

Yes, the CP200 requires a rib.

Also, the CP200 is programmed by CPS, not RSS.

fireman54 · Post by **fireman54** » Sun May 21, 2006 7:45 am

I am sorry cps verson for the cp150 and 200
W

Where can I find the adapter to get the cable to fit the rib

HLA · Post by **HLA** » Sun May 21, 2006 8:00 am

i think radio shack still has those adaptors or you can just get the regular 25 pin connector and replace your end.

fireman54 · Post by **fireman54** » Mon May 22, 2006 8:16 am

I am still getting error 512

whats up?

fireman54 · Post by **fireman54** » Mon May 22, 2006 8:23 am

who can I call to help me with this problem?

fireman54 · Post by **fireman54** » Mon May 22, 2006 8:46 am

What version of software should I be using also?

Post by **wavetar** » Mon May 22, 2006 3:39 pm

You obviously aren't using a factory cable, so without physically seeing what you actually have for hardware, it's difficult to troubleshoot your problem.

The part number for the CP200 series CPS is RVN4191, the latest version is 5.04.

Todd

fireman54 · Post by **fireman54** » Mon May 22, 2006 4:01 pm

I am using a motorola rib not a aftermarket and using the cable that does cp 200, p1225, and the gp300.

The software that I have is version 1.0 and the radio's are version 3.0 is that the reason?

stvnd53 · Post by **stvnd53** » Tue May 23, 2006 12:56 am

The cp200 plugs into the side of the radio ! gp300 & 1225 are diferent

Post by **wavetar** » Tue May 23, 2006 9:05 am

fireman54 wrote:I am using a motorola rib not a aftermarket and using the cable that does cp 200, p1225, and the gp300.

The software that I have is version 1.0 and the radio's are version 3.0 is that the reason?

Yes, you may be using a Motorola RIB, but you are NOT using a Motorola cable, as it is not the same cable for the CP200, P1225, and GP300...in fact it's 3 completely different cables.

Your software version is ancient. It may be the problem, or it may be your cable. Hard to know unless you try a known-good CP200 programming set-up.

Todd

cp200 programming problems

cp200 programming problems

cable

cp200

still having problems

question

cable

Re: cable