Hello All,
I have an IFR 1600S which I have had for years. Suddenly I am now getting spurs on the Spectrum Analyzer every 10mhz. If I set the scan to 50 or 100 mhz, I don't see them as I assume they get lost in the large resolution bandwidth. When I get the scan down around 500khz, I can see the spur to the side and if I change frequency to center the spur, it disappears when it gets close to center. This occurs regardless of input chosen and whether or not an antenna is connected.
Another issue, which may be related or offer a clue to the other problem, is that when I run the tracking generator, the output amplitude is going up and down as the frequency sweeps. I checked this with a scope hooked up to the output. I was having a hell of a time trying to tune a can when I decided to check this out.
It does pass the self tests, however, one time test #17 (I think it was a tracking test) failed. Leaving it off overnight seemed to make the problem disappear as it passed the next morning.
Can anyone offer any advice? I re-seated all of the cards and rf connectors. We put the output of the power supply on a scope and it seemed clean.
Anything else to check for?
73,
Michael
N1PLH
- Board index Focused Discussion Test Equipment & RF Equipment Alignment
- Search
-
- It is currently Thu May 23, 2024 7:49 am
- All times are UTC-08:00
1600S with 10mhz spurs
This forum exists for the purposes for discussing service monitors (This includes but is not limited to Motorola, HP, Aeroflex, GD, etc). Additional topics allowed include test procedures, interpretation of test results, where to find information about specific tests, antenna VSWR, return loss testing, duplexer and filter alignment, etc.
Moderator: Queue Moderator
-
- Posts: 40
- Joined: Sat Mar 29, 2003 4:16 pm
Return to “Test Equipment & RF Equipment Alignment”
Jump to
- Administrative
- ↳ Announcements and Forum News
- ↳ Forum Rules
- General
- ↳ General Motorola Solutions & Legacy Radio Discussion
- ↳ Radio Programming
- ↳ Software & Firmware Releases & Issues
- ↳ Codeplug Information
- ↳ NFPA 1802 Discussion
- Current Motorola Solutions Public Safety / Astro Product Line
- ↳ APX NEXT
- ↳ APX Series Subscribers
- ↳ ASTRO Series (Astro Saber, Spectra, XTS3000/3500) Subscribers
- ↳ ASTRO25 Series (XTS/XTL 1500/2500/5000) Subscribers
- ↳ ASTRO Experimental - How to do things a little out of the box
- ↳ ASTRO Products Feature Requests & Future Speculation
- ↳ Legacy Batboard Motorola ASTRO (VSELP/IMBE/AMBE) Equipment Forum
- Current Motorola Solutions Professional / Business Product Lines
- ↳ MotoTRBO ION Devices
- ↳ Motorola CP/CM Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (4xxx/6xxx) 1.0 Series Subscribers
- ↳ MotoTRBO Portables and Mobiles (3xxx/5xxx/7xxx/SL) 2.0 Series Subscribers
- ↳ MotoTRBO Repeaters, Trunking, and Site Infrastructure
- ↳ MotoTRBO 3rd Party Application Discussion & Support
- ↳ MotoTRBO/Business Products Feature Requests & Future Speculation
- ↳ Experimental - How to do things a little out of the box
- Motorola System Infrastructure (Consoles, Base Stations, Repeaters, Trunking, etc.)
- ↳ Smartnet/Smartzone/Project 25 (Phase I/II) Systems
- ↳ Base Stations, Repeaters, General Infrastructure
- ↳ Consoles
- ↳ Experimental - Mods, and how to do things a little out of the box
- ↳ Infrastructure Product Feature Requests & Future Speculation
- Focused Discussion
- ↳ Motorola Digital and Voice Paging
- ↳ Converting Motorola Equipment to 900MHz Amateur
- ↳ Test Equipment & RF Equipment Alignment
- ↳ Vehicle Radio Installs
- ↳ Experimental and Next Generation LMR
- ↳ Motorola Digital Radio Compatability
- Off-Topic Discussion
- ↳ Vehicle Warning Equipment Discussion
- ↳ Computer/Technical Assistance
- ↳ Knowledge Base